SECTION 10440

DOOR AND ROOM SIGNS
				
	[[Delete sign type articles that do not apply]]
NOTE ** This section is based on products manufactured by Scott 
Sign Systems, Inc., at the following address:
NOTE **      7524 Commerce Place
NOTE **      Sarasota, FL 34243-5020
NOTE **      Telephone 941-355-5171, FAX 941-351-1787
NOTE **      Toll Free Telephone 800-237-9447.
NOTE ** 
NOTE ** Scott Sign Systems offers a complete line of letters, 
logos and architectural sign systems.
NOTE ** 
NOTE ** SECTION 10445 - DOOR AND ROOM SIGNS, Copyright 1998.

PART 1	GENERAL

1.01	SECTION INCLUDES

A.	Door Signs.

B.	Room Signs.

C.	Dimensional Letters and Numbers.

1.02	REFERENCES

A.	ADAAG - Americans with Disabilities Act Accessibility 
Guidelines; U.S. Architectural and Transportation Barriers 
Compliance Board.
B.	Department of Justice - 28 CFR Part 35 Nondiscrimination 
on the Basis of Disability In State and Local Government 
Services; Final Rule: published Federal Register / Vol. 
56, No. 144 / Friday, July 20, 1991. ÒThis rule implements 
subtitle A of title II of the Americans with Disabilities 
Act, Public Law 101-336, ... ... [ADA]

1.03	SUBMITTALS

A.	Submit under provisions of Section 01300.

B.	Product Data:  Manufacturer's descriptive literature for 
sign types specified, including components and 
accessories.

C.	Shop Drawings:  Indicate location of each individual sign 
in the project.
NOTE ** Delete the following paragraph if specifying colors in 
this section. 

D.	Verification Samples:  One full size sample sign of type, 
style and color specified, including method of attachment.

E.	Manufacturer's instructions:  Printed installation 
instructions for each product.

1.04	QUALITY ASSURANCE

A.	Regulatory Requirements:  Sign types to comply with ADAAG 
requirements, The Americans with Disabilities Act - 
1990(ADA) and ANSI A117.1 - 1992.

1.05	DELIVERY, STORAGE, AND HANDLING

A.	Store products of this section in manufacturer's unopened 
packaging until installation.

B.	Maintain dry, climate controlled storage area for products 
of this section until installation of products.


PART 2	PRODUCTS

2.01	MANUFACTURERS

A.	Acceptable Manufacturer:  Scott Sign Systems, Inc. 7524 
Commerce Place Sarasota, FL 34243 Toll Free Telephone: 
800-237-9447 Telephone: (941) 355-5171 24 HR Fax: (941) 
351-1787.
NOTE ** Delete one of the two following paragraphs; coordinate 
with Division 01 requirements. 

B.	Requests for substitutions will be considered in 
accordance with provisions of Section 01600.

C.	Substitutions:  Approved equal must submit their signage 
products to the Architect 10 days prior to the bid date 
for approval to be considered as an equal.
NOTE ** Delete following paragraph if substitutions not permitted. 

D.	Unless otherwise specified for an individual product or 
material, supply all products specified in this section 
from the same manufacturer.

2.02	MANUFACTURED UNITS 

 [[[Delete Sign Type Articles that do not apply.]]]
NOTE ** Delete paragraphs specifying products not required; 
consult manufacturer's catalog for available options and insert in 
paragraph.
NOTE ** If not selecting colors at time of issue of Project 
Manual, retain sub-paragraph deferring color selection and 
coordinate with requirements for Samples in SUBMITTALS Article of 
PART 1; if specifying more than one color or size, retain sub-
paragraph which refers to SCHEDULES Article. 

A.	Acrylic Braille Room Signs:
1.	Acceptable product:  Series S1000
2.	Colors:  Face color __________; letter color ________.
3.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
4.	Colors:  Specified in SCHEDULES Article of this 
section.
5.	Sign size:  _____ inches by ______ inches.
6.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
7.	Corners: Radius
8.	Header: Polished Gold, Polished Silver, Brushed Gold, 
Brushed Silver
9.	Header: None
10.	Lettering:  Applied minimum 5/8 inch high, raised 1/32 
inch, with Grade 2 Brailldot coding.
11.	Lettering Style: Scott HM, Specify
12.	Sign frames: Aluminum, Plastic
13.	Sign frames: None
14.	Installation Method: Specify

B.	Acrylic Room/Directional Signs:
1.	Acceptable product:  Series S1000
2.	Colors:  Face color __________; letter color ________.
3.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
4.	Colors:  Specified in SCHEDULES Article of this 
section.
5.	Sign size:  _____ inches by ______ inches.
6.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
7.	Corners: Radius
8.	Header: Polished Gold, Polished Silver, Brushed Gold, 
Brushed Silver
9.	Header: None
10.	Lettering:  Applied minimum 5/8 inch high, minimum 
raised 1/32 inch, with Grade 2 Brailldot coding.
11.	Lettering: Sub-surface applied.
12.	Lettering Style: ______________________.
13.	Sign frames: Aluminum, Plastic
14.	Sign frames: None
15.	Installation Method: Specify

C.	Changeable Insert Identification Signs:
1.	Acceptable product:  Scott Series S2000
2.	Sign Types:  As indicated.
3.	Colors:  Face color  __________; graphics and letter 
colors manufacturer's standard.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Corners: Radius
10.	Insert Size/Quantity: Specify
11.	Insert Material: Specify
12.	Graphics/Lettering:  As indicated.
13.	Installation Method: VHB, Holes Drilled, Specify

D.	Acrylic Room Number Signs:
1.	Acceptable product:  Scott Signs Braillplaques
2.	Sign Types: As indicated.
3.	Colors:  Face color __________; letter color ________.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  ______ inches by _____ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Lettering:  Applied 5/8 inch high, raised 1/32 inch, 
with Grade 2 Brailletter coding.
10.	Lettering Style: Scott HM
11.	Sign frames: Plastic
12.	Installation Method: VHB, Holes Drilled, Specify

E.	Injection Molded Signs:
1.	Acceptable product:  Scott-ADA Molded Acrylic Plaques
2.	Colors:  Face color: Black, White, Almond, Gray, Clear 
non-glare painted __________; graphics and letter 
color ________.
3.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
4.	Colors:  Specified in SCHEDULES Article of this 
section.
5.	Sign size:  3 inches by 6 inches.
6.	Sign size:  6 inches by 6 inches.
7.	Sign size:  8 inches by 6 inches.
8.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
9.	Corners: Square
10.	Graphics:  International symbols for indicated 
information.
11.	Lettering:  Minimum 5/8 inch high integral copy, 
raised 1/32 inch, with Grade 2 Braille coding.
12.	Lettering Style: Scott HM
13.	Sign frames:  None
14.	Installation method: VHB, Holes Drilled, Specify

F.	Surface applied lettered Identification Signs:
1.	Acceptable product:  Scott Acrylic Plaques
2.	Sign Types:  As indicated.
3.	Colors:  Face color  __________; graphics and letter 
colors manufacturer's standard.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Corners: Radius
10.	Graphics/Lettering:  As indicated.
11.	Lettering Style: _______________________.
12.	Sign Frames: Aluminum, Plastic
13.	Sign Frames: None
14.	Installation Method: VHB, Holes Drilled, Specify

G.	Sub-surface lettered Identification Signs:
1.	Acceptable product: Scott Acrylic Plaques
2.	Sign Types:  As indicated.
3.	Colors:  Face color ________; graphics and letter 
colors manufacturer's standard.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Radius
9.	Corners: Square
10.	Graphics/Lettering:  As indicated.
11.	Lettering Style: _____________________.
12.	Sign frames: Aluminum, Plastic
13.	Sign frames: None
14.	Installation Method: VHB, Holes Drilled, Specify

H.	Interior Photopolymer Signs:
1.	Acceptable product: Scott Photopolymer
2.	Sign Type: As indicated.
3.	Sign Types:  As indicated.
4.	Colors:  Face color __________; graphics and 
	letter color ________.
5.	Colors:  Selected by Architect from 	manufacturer's 
full range of available colors.
6.	Colors:  Specified in SCHEDULES Article of this 
	section.
7.	Sign size:  _____ inches by ______ inches.
8.	Sign sizes:  Specified in SCHEDULES Article of 	this 
section.
9.	Corners: Square
10.	Corners: Radius
11.	Graphics/Lettering:  As indicated.
12.	Lettering style:  ________________.
13.	Installation Method: VHB, Specify

I.	Changeable frame system:
1.	Acceptable product: Scott Snap Plate System
2.	Sign Type: As indicated.
3.	Frame Color: Black, White, Almond, Gray
4.	Plate Color: Clear non-glare, Black, White, 	Almond, 
Gray
5.	Sign size: 2 x 10, 3 x 3 , 4 x 4, 6 x 6, 8 x 8, 
8.5 x 11
6.	Corners: Square
7.	Graphics/Lettering: As indicated.
8.	Installation Method: VHB, Holes Drilled, Specify

J. Dimensional Acrylic Room Signs:
1.	Acceptable Product: Scott Series S4000
2.	Sign Types: As indicated.
3.	Colors: Border color: _____________; Letter color: 
________________.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Edge: Polished, Beveled
10.	Sub-surface Background Material: Polished Gold, 
Polished Silver, Brushed Gold, Brushed Silver
11.	Lettering:  Applied minimum 5/8 inch high, raised 
minimum 1/32 inch, with Grade 2 Brailldot coding.
12.	Lettering: Sub-surface applied
13.	Lettering Style: Scott HM, Specify
14.	Sign frames: None
15.	Installation Method: VHB, Specify

K.	Back-Engraved Signs:
1.	Acceptable product:  Scott Signs; clear plastic front 
face, letters/graphics engraved through color layer, 
back-filled with letter color, specify.
2.	Sign Types:  As indicated.
3.	Colors:  Face color __________; graphics and letter 
color ________.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Corners: Radius
10.	Graphics/Lettering:  As indicated.
11.	Lettering style:  ________________.
12.	Installation Method: VHB, Holes Drilled, Specify

L.	Etched Metal Signs:
1.	Acceptable product:  Scott Signs Metal Etched
2.	Acceptable product:  Scott Signs Magnesium
3.	Sign Types:  As indicated.
4.	Colors:  Face color __________; graphics and letter 
color ________.
5.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
6.	Colors:  Specified in SCHEDULES Article of this 
section.
7.	Sign size:  _____ inches by ______ inches.
8.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
9.	Corners: Square
10.	Corners: Radius
11.	Graphics/Lettering:  As indicated.
12.	Lettering style:  ________________.
13.	Installation Method: VHB, Holes Drilled, Specify

M.	ADA Engraved Signs:
1.	Acceptable product:  Scott ADA Engraved Alternative
2.	Sign Types:  As indicated.
3.	Colors:  Face color __________; graphics and letter 
color ________.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this
8.	Corners: Square
9.	Corners: Radius
10.	Lettering:  Applied, raised 1/32 inch, with Grade 2 
Braille coding in background.
11.	Graphics/Lettering:  As indicated.
12.	Lettering Style: ___________________
13.	Installation Method: VHB, Holes Drilled, Specify

N.	Engraved Signs:
1.	Acceptable product:  Scott Signs Engraved
2.	Sign Types:  As indicated.
3.	Colors:  Face color __________; graphics and letter 
color ________.
4.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
5.	Colors:  Specified in SCHEDULES Article of this 
section.
6.	Sign size:  _____ inches by ______ inches.
7.	Sign sizes:  Specified in SCHEDULES Article of this 
section.
8.	Corners: Square
9.	Corners: Radius
10.	Graphics/Lettering:  As indicated.
11.	Lettering Style: _____________________
12.	Installation Method: VHB, Holes Drilled, Specify

O.	Accessories:  Installation fasteners specified in 
manufacturer's instructions.

2.03	DIMENSIONAL LETTERS AND NUMBERS

	A.	Molded Acrylic Letters and Numbers
1.	Acceptable Product: Scott Injection Molded Letters
2.	Sign Type:  As indicated.
3.	Colors: Black, White
4.	Colors: Painted
5.	Colors: Two Tone/Hot-Stamped, Specify side and face 
color.
6.	Colors: Painted Gold Sides, Polished Gold Face
7.	Colors: Painted Gold Sides, Brushed Gold Face
8.	Colors: Painted Silver Sides, Polished Silver Face
9.	Colors: Painted Silver Sides, Brushed Silver Face
10.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
11.	Colors:  Specified in SCHEDULES Article of this 
section.
12.	Letter Size: _____________________.
13.	Letter Thickness: 1/8Ó
14.	Letter Style: ______________________.
15.	Installation Method: Stickee, VHB, None, Specify

	B.	Cutout Letters and Numbers
1.	Acceptable Product: Scott Cut Acrylic Letters
2.	Sign Type:  As indicated.
3.	Colors: Black, White, Red, Blue
4.	Colors: Painted
5.	Colors: Painted Sides, Laminate Mica Face
6.	Colors: Painted Sides, Two Tone/Hot-Stamped Face
7.	Colors:  Selected by Architect from manufacturer's 
full range of available colors.
8.	Colors:  Specified in SCHEDULES Article of this 
section.
9.	Letter Size: _____________________.
10.	Letter Thickness: 1/8Ó, 1/4Ó, 1/2Ó
11.	Letter Style: ______________________.
12.	Installation Method: VHB, None, Specify

C.	Exterior Acrylic Letters and Numbers
1.	Acceptable Product: Scott Vacuum Formed Letters
2.	Sign Type:  As indicated.
3.	Colors: Standard Formed Color
4.	Colors: Painted
5.	Colors: Specified in SCHEDULES Article of this 
section.
6.	Letter Size: _____________________.
7.	Letter Style: ______________________.
8.	Installation Method: Specify, Flange, Pad, Stud, Pad & 
Stud Combination, Inside Bracket, None.

D.	Metal Letters and Numbers
1.	Acceptable Product: Scott Signs Cut Metal Letters
2.	Sign Type:  As indicated.
3.	Material: Aluminum
4.	Material: Brass
5.	Finish: Polished Face, Satin Sides
6.	Finish: Satin/Brushed Face, Satin Sides
7.	Finish: Painted color as selected by Architect from 
manufacturers full range of available colors.
8.	Finish: As specified in SCHEDULES Article of this 
section.
9.	Letter Size: _____________________.
10.	Letter Thickness: 1/8Ó, 1/4Ó, 3/8Ó, 1/2Ó
11.	Letter Style: ______________________.
12.	Graphics/Lettering: As indicated.
13.	Installation Method: Specify, Stud, Projected Stud, 
None.

E.	Cast Metal Letters and Numbers
1.	Acceptable Product: Scott Signs Cast Metal Letters
2.	Sign Type:  As indicated.
3.	Material: Aluminum
4.	Material: Bronze
5.	Finish: Polished Face, Satin Sides
6.	Finish: Satin/Brushed Face, Satin Sides
7.	Finish: Painted color as selected by Architect from 
manufacturers full range of available colors.
8.	Finish: As specified in SCHEDULES Article of this 
section.
9.	Letter Size: _____________________.
10.	Letter Style: ______________________.
11.	Graphics/Lettering: As indicated.
12.	Installation Method: Specify, Stud, Projected Stud, 
None.

F.	Vinyl Letters and Numbers
1.	Acceptable Product: Scott Vinyl Letters
2.	Sign Type:  As indicated.
3.	Colors: Standard
4.	Colors: Metallic
5.	Colors: Reflective White
6.	Colors: Frosted
7.	Colors: Selected by Architect from manufacturer's full 
range of available colors.
8.	Colors:  Specified in SCHEDULES Article of this 
section.
9.	Letter Size: _____________________.
10.	Letter Style: ______________________.
11.	Graphics/Lettering: As indicated.
12.	Installation Method: Adhesive Faced (for sub-surface 
mounting), Adhesive Backed (for regular mounting)

PART 3	EXECUTION

3.01	EXAMINATION

A.	Verify that surfaces to receive signs have been finished, 
and that finishes are dry and correctly cured.

3.02	INSTALLATION

A.	Install room and door signs in accordance with 
manufacturer's printed installation instructions.

B.	Locate signs in accordance with approved shop drawings and 
ADA requirements.
NOTE ** The following Article will assist in preparing a door and 
room sign schedule for the project. 

3.03	SCHEDULES

		[[Indicate Sign Schedule as it applies]]

A.	Sign Schedule:
1.	First Floor:
	a.	Sign Type: Specify
	b.	Background Color: Specify
	c.	Letter Style: Specify
	d. 	Letter Color: Specify
	1.	Room 101:  Legend "WAITING ROOM"; size 8 
	inches by 8 inches.
	2.	Door 121:  Legend "AUTHORIZED PERSONNEL 
	ONLY"; size 2 inches high by 12 inches long.

	END OF SECTION